Introduction

BatteryProtect BP-65 – 65AMP – 6-35 VDC

Features:

• The BatteryProtect disconnects the battery from non essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
• 12/24V auto ranging The BatteryProtect automatically detects system voltage
• Programming made easy The BatteryProtect can be set to engage / disengage at several different voltages. The seven segment display will indicate which setting has been chosen.
• A special setting for Li-ion batteries In this mode the BatteryProtect can be controlled by the VE.Bus BMS. Note: the BatteryProtect can also be used as a charge interrupter in between a battery charger and a Li-ion battery. See connection diagram in the manual.
• Ultra low current consumption This is important in case of Li-ion batteries, especially after low voltage shutdown. Please see our Li-ion battery datasheet and the VE.Bus BMS manual for more information.
• Over voltage protection To prevent damage to sensitive loads due to over voltage, the load is disconnected whenever the DC voltage exceeds 16V respectively 32V.
• Ignition proof No relays but MOSFET switches, and therefore no sparks.
• Delayed alarm output The alarm output is activated if the battery voltage drops below the preset disconnect level during more than 12 seconds. Starting the engine will therefore not activate the alarm. The alarm output is a short circuit proof open collector output to the negative (minus) rail, max. current 50 mA. The alarm output is typically used to activate a buzzer, LED or relay. Delayed load disconnect and delayed reconnect The load will be disconnected 90 seconds after the alarm has been activated. If the battery voltage increases again to the connect threshold within this time period (after the engine has been started for example), the load will not be disconnected. The load will be reconnected 30 seconds after the battery voltage has increased to more than the preset reconnect voltage.

Warranty Info

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Please contact your dealer for any returns, repairs or support issues related to this product.

BatteryProtect 12 / 24V–BatteryProtect disconnects the battery from non-essential loads before it is fully discharged (which will damage the battery) or before there is enough power to start the engine. The battery protector is a one-way device. It can only handle current in one direction, so it can handle both the current to the load and the current from the charger, but it cannot handle two currents at the same time. In addition, current can only flow from the battery terminal to the load terminal. If a load is used, the battery is connected to the battery terminal, and if a charger is used, the charger is connected to the battery terminal. !!!!—-
PRODUCT ID: 82905
SKU: NVN-82905
CSKU: CWR-82905
REWRITE: 94016-victron-batteryprotect-bp-65-65amp-6-35
MPN: BPR000065400
UPC: 8719076034193
ASIN: B01N6ATT8C
WSKU:
SSKU:
KSKU:
GSKU:
MSKU:
LSKU:
NAME: Victron BatteryProtect BP-65 – 65AMP – 6-35 VDC
NAME_EX: VICTRON BATTERYPROTECT 12/24V-65A
PTITLE: Victron BatteryProtect BP-65 – 65AMP – 6-35 VDC
TYPE: Electrical | Battery Management
VENDOR: Victron Energy
Google Category: VEHICLES & PARTS > VEHICLE PARTS & ACCESSORIES > WATERCRAFT PARTS & ACCESSORIES
Amazon Category: CE
Amazon Title: Victron BatteryProtect BP-65-65AMP – 6-35 VDC [BPR000065400]
Google Title: Victron Battery Protect 12/24V 65A 100A & 220A – BP-65A
Amazon Category: CE
Gtags:

GSpecs: